Questions? Feedback? powered by Olark live chat software
844-866-6348 Info@RapidFirePS4.com    English French German Filipino Italian Polish Portuguese Russian Spanish Swedish Arabic Chinese (Simplified)

Rapid Fire PS4 Mod Installation

Before you install your RapidFirePS4 Mod you will need a few things. You will need:
You will need a #0 Phillips head Screwdriver to install your Rapid Fire PS4 Mod

a #0 Phillips Screw Driver

You will need a small amount of fine solder

Solder

You will need a 15w Soldering Iron to install your PS4 Rapid Fire Mod

a Low Temp Soldering Iron

You will need a small amount of hot glue or double sided tape to install your PS4 Mod

Hot Glue / Double Sided Tape

Step 1

1a. Gripping the controller bottom with your left index finger and thumb and the top shell with your right index finger and thumb, Pull the controller apart until a snap sound is heard. Open the controller slightly like a clam shell. Hold the controller as shown and push the bottom shell forward allowing its full removal.

Open Your PS4 Controller to Install Your RapidFirePS4 Rapid Fire PS4 Mod

Be careful not to damage your Light Bar Ribbon when removing the bottom shell. Grip it between your fingers and pull it from its pressure clasp.

Step Two – PS4 Controller Version Identification

Our PS4 Rapid Fire is compatible with the original PS4 Controller Board

Version One Controller Board

Our PS4 Rapid Fire is compatible with the second version of the PS4 Controller Board

Version Two Controller Board

Our PS4 Rapid Fire is compatible with the latest version of the PS4 Controller Board

Version Three Controller Board

Step 3

3a. Remove the Battery completely by unplugging it. Set it aside

Remove the Battery completely to install your rapidfireps4 mod

3b. Remove Battery Tray completely. Remove the Touchpad Ribbon cable and straighten it out.

Remove the Battery Tray and unplug the Touchpad Ribbon

3c. Remove the securing screw from the middle of the board.

Remove the middle securing screw to install your PS4 Rapid Fire Mod

3d. Lift the board while leaving the skeleton inside the controller shell. Rotate the Board 180 degrees while keeping it raised above the skeleton.

Rotate the Controller Board 180 degrees to access the front of the board

3e. Solder the RED wire to the MIDDLE via as pictured. (Version 3 ONLY)

Solder the RED wire to the MIDDLE via

3f. Lay Rapid Fire PCB on Controller Board and Solder the TP point to Touch Pad switch leg.

Solder the TP point to the touchpad switch leg

3g. Rotate Controller Board back around and Insert it back in to place. Be mindful of the touchpad ribbon cable. Move the RED wire to the left. Apply 1″ piece of double sided tape or thin stripe of hot glue and affix the mod to the board. Secure the Board with the inside Screw. Finally bend the RED wire to the right as shown.

Affix-the-Mod-to-the-Controller-board

Ensure that the alignment holes are properly aligned while doing this to ensure a proper fit the first time, every time.
Solder the TP point to the touchpad switch leg

3h. Solder both wire leads like so:

Solder the WHITE wires to to the R3 and L3 points

Step 4

4a. Insert Light Bar Ribbon with Blue Tab facing out.

Insert blue tab in to the pressure clasp BLUE side out

4b. Insert Shell like pictured:

Install Bottom Shell

4c. Ensure ribbon is properly seated

Ensure-the-ribbon-is-laying-properly

4d. Close the shell and insert the four (4) screws.

 

Troubleshooting Your Rapid Fire Mod Installation

Having more trouble? Contact us right now! Info@RapidFirePS4.com

Shoot Faster. Do More. RapidFirePS4.

Subscribe To Save

Subscribe To Save

 

Join our mailing list to receive the latest news and updates from our team.

Save $5 on your next Rapid Fire PS4 Controller or Rapid Fire PS4 Mod by subscribing!

You have Successfully Subscribed!